whattimeisit.blog
Time standards

Leap Seconds Explained: Why They’re Added to UTC

Leap seconds are occasional one-second adjustments to UTC that keep it close to Earth’s uneven rotation. Here’s who decides when they happen, what could change by 2035, and why a negative leap second is possible.

By Leo, editorUpdated November 10, 20268 min read3 sources
Atomic clock and brass clock representing a leap second
Illustration created for WhatTimeIsIt.blog.
Quick answer

A leap second is a one-second adjustment to Coordinated Universal Time (UTC), used to keep it within 0.9 seconds of Earth-rotation time, UT1. There have been 27 added since 1972; the most recent was at the end of December 31, 2016. The IERS monitors Earth’s rotation and determines when an adjustment is needed, while a 2022 CGPM resolution set a goal to increase the permitted UTC–UT1 difference in or before 2035. NIST’s leap-second FAQ explains the current system.

  • I27 leap seconds have been added since 1972.
  • IIThe last leap second was December 31, 2016.
  • IIIIERS monitors UT1–UTC and determines when a leap second is needed.
  • IVThe CGPM decided to increase the maximum UT1–UTC difference by 2035.
  • VA negative leap second is possible, but none has occurred.
I

What is a leap second?

A leap second is an occasional one-second adjustment to UTC, the internationally agreed time scale used for civil timekeeping. Unlike a leap year, it does not follow a fixed calendar rule. It is introduced only when measurements of Earth’s rotation show that the difference between UTC and astronomical time, called UT1, is approaching the allowed limit.

UTC is built from atomic time, which advances at a highly regular rate. UT1 reflects Earth’s actual rotation, which varies. The leap-second system has kept those two scales within 0.9 seconds of one another. The NIST FAQ explains that a positive leap second has the sequence 23:59:59, then 23:59:60, then 00:00:00 on the next date.

That extra label is not a new time zone or a change to the calendar date. It is a brief adjustment to the count of seconds in UTC. For background on the time scale itself, see our guide to what UTC is or check the current UTC time.

II

Why do we need leap seconds?

Atomic clocks define seconds with exceptional regularity, but Earth does not rotate at a perfectly constant rate. Its rotation varies, and over long intervals it has been gradually slowing. As a result, the time measured by Earth’s rotation can drift against atomic time. Leap seconds have been the method for keeping UTC close to UT1, the astronomical time scale based on Earth’s rotation.

UTC is produced by the BIPM at the same rate as International Atomic Time (TAI), differing from TAI by an integral number of seconds. Leap seconds change that whole-second offset when needed. The BIPM’s account of CGPM Resolution 4 describes the link between the UTC–TAI offset and agreement between UTC and UT1.

For most everyday tasks, the difference is not something you need to calculate. It matters to systems that rely on very precise timing, as well as scientific and astronomical work. Atomic clocks provide the stable ticking behind atomic time; learn more in our guide to atomic clocks. UTC is the practical reference for coordinating clocks, while UT1 tracks the less regular rotation of the planet.

III

Who decides when a leap second happens?

The International Earth Rotation and Reference Systems Service (IERS) measures Earth’s rotation and publishes the difference between UT1 and UTC. Under the procedure described in ITU-R Recommendation TF.460-6, a leap second is applied when IERS observations indicate that UT1–UTC is predicted to approach 0.9 seconds. NIST says positive leap seconds are usually added when UTC is ahead of UT1 by 0.4 seconds or more.

The IERS determines whether a correction is needed; this is not a decision made by a phone manufacturer, a local government, or an individual timekeeper. The BIPM produces UTC from international clock data, while national laboratories maintain real-time realizations of UTC for practical use. The NIST explanation of UTC and related time scales distinguishes calculated UTC from the real-time versions maintained by laboratories.

Leap seconds have generally been placed at the end of June or December, at the end of a UTC day. A notice of an upcoming adjustment gives time services and other users a chance to prepare. To convert a UTC time into local time, use the time zone converter; a leap second is a UTC adjustment, not a daylight saving time change.

IV

How many leap seconds have been added?

Twenty-seven positive leap seconds have been added since 1972. The latest was inserted at the end of December 31, 2016. As of November 10, 2026, no later leap second has been added. The interval between adjustments has not followed a dependable schedule: Earth’s rotation varies, so future leap seconds cannot be predicted years in advance.

There is an important distinction between the 27 leap seconds and the initial correction associated with the start of the modern system. NIST notes that when corrections began in 1972, UTC received a necessary correction of 10 seconds. That historical offset is not the same thing as 27 later one-second insertions. A leap second is not an extra calendar day, and it is not the same as the February 29 added in a leap year.

Leap-second basics — source: NIST
QuestionAnswer
How many have been added?27 since 1972
Most recent additionDecember 31, 2016
Where is one normally placed?At the end of a UTC day in June or December

For ordinary calendar arithmetic, leap seconds rarely affect date calculations. If you are comparing exact elapsed times or timestamps around an adjustment, make sure the software or time scale you use accounts for it.

V

What does a positive leap second look like?

A positive leap second adds an extra second to the final UTC minute of an announced date. Instead of moving directly from 23:59:59 to 00:00:00, UTC can label the added second 23:59:60. The clock then advances to 00:00:00 on the next date. This unusual timestamp is valid for UTC during the adjustment, even though many everyday clocks and software systems are not designed to display it.

For example, when a positive leap second occurs at the end of a UTC date, a timestamped sequence may read 23:59:58, 23:59:59, 23:59:60, and then 00:00:00. This is a change in the UTC second sequence, not an instruction to reset every local clock manually. Local time zones express their time as offsets from UTC, so the local representation depends on the offset in effect at that location.

One common mistake is to assume every minute always contains exactly 60 labeled seconds in every time scale and software environment. Another is to confuse a leap second with daylight saving time, which changes local clock readings according to regional rules. Use a time difference tool to compare ordinary local times, and consult your system’s timekeeping documentation if you need exact timestamp handling around a leap-second event.

VI

Could there be a negative leap second?

Yes. The rules allow a negative leap second if changes in Earth’s rotation make one necessary, although only positive leap seconds have occurred so far. A negative adjustment would remove a second from UTC rather than add one. NIST gives the illustrative sequence 23:59:57, 23:59:58, then 00:00:00 at the start of the following date: the usual 23:59:59 would be omitted.

The possibility matters because many systems have only had to deal with positive leap seconds, and a negative adjustment would create a different edge case for clocks, logs, and time-sensitive software. The CGPM’s 2022 resolution notes that observations of Earth’s rotation indicate a possible need for a first negative leap second, which has never been foreseen or tested. That is a possibility identified in the resolution, not an announcement that one is scheduled.

Do not infer a negative leap second from a clock running fast, a time-zone change, or a daylight saving time transition. It would be a formal change to UTC’s sequence of seconds. For converting timestamps or checking elapsed time, tools such as a Unix timestamp converter can be useful, but confirm how a particular system represents leap seconds before relying on it for precision work.

VII

What did the 2022 resolution change?

At its 2022 meeting, the General Conference on Weights and Measures (CGPM) decided that the maximum permitted value of UT1–UTC will be increased in or before 2035. The existing leap-second approach keeps the difference within 0.9 seconds. Increasing the permitted maximum is intended to allow UTC to continue without frequent one-second discontinuities for a longer period.

The resolution did not itself specify the new maximum. It asked the International Committee for Weights and Measures (CIPM) to consult the ITU and other affected organizations about a value that would ensure UTC continuity for at least a century, and to prepare an implementation plan by or before 2035. It also asked for a future review period and for a proposed resolution to be prepared for agreement at the 28th CGPM in 2026. Those are the tasks described by the BIPM resolution; the source does not provide a final new threshold.

What Resolution 4 says — source: BIPM
TopicResolution detail
Maximum UT1–UTCIncrease in or before 2035
New valueTo be developed after consultation
GoalUTC continuity for at least a century

So the 2035 milestone is about raising the allowed difference, not an announced date for the next leap second or an immediate end to UTC.

VIII

Why do leap seconds matter to computers and everyday clocks?

For a person checking a wall clock, a one-second adjustment may pass unnoticed. For computer systems that coordinate events across networks, however, a discontinuity can be difficult to handle. The CGPM resolution warns that leap-second discontinuities can risk serious malfunctions in critical digital infrastructure, including global navigation satellite systems (GNSS), telecommunications, and energy transmission systems. It also notes that operators have used different, unstandardized methods to introduce leap seconds.

That variety can make systems disagree about how to represent or distribute the adjusted second. The risk is not that every device will fail, but that systems with strict timing requirements need a clear, consistent method. This is one reason the CGPM called for a new maximum UT1–UTC value and further coordination among organizations affected by the change.

Everyday time tools remain useful for routine planning: a hours calculator can total ordinary work or travel intervals, and a date calculator can count calendar days. Those tools answer different questions from high-precision timekeeping. If you are handling scientific data, network logs, or infrastructure timestamps, check which time scale is recorded and how the system treats leap seconds rather than assuming every timestamp is plain UTC.

?

Questions people ask

When was the last leap second?

The last leap second was added at the end of December 31, 2016. It was the 27th positive leap second added since 1972. NIST’s FAQ describes the leap-second system and its timing.

Who decides whether to add a leap second?

The IERS monitors Earth’s rotation and publishes the difference between UT1 and UTC. Under the current procedure, a leap second is applied when measurements indicate that UT1–UTC is predicted to approach 0.9 seconds. The BIPM produces UTC from international timekeeping data.

Does every year have a leap second?

No. Leap seconds are added only when measurements show an adjustment is needed; they do not follow a fixed yearly rule. There have been 27 since 1972, and the most recent was December 31, 2016. Leap years, by contrast, follow calendar rules.

Has a negative leap second ever happened?

No. Only positive leap seconds have occurred, but the system allows a negative adjustment if Earth’s rotation makes one necessary. A negative leap second would remove a second from the UTC sequence; it has never been inserted.

Will leap seconds stop by 2035?

The 2022 CGPM resolution decided to increase the maximum permitted UT1–UTC difference in or before 2035. It did not announce a final new threshold or a date for the last leap second. The resolution asked for consultation and an implementation plan before the change.

Is a leap second the same as a leap year?

No. A leap second is an occasional one-second UTC adjustment intended to keep UTC close to Earth-rotation time. A leap year adds a calendar day to February under the Gregorian calendar’s rules. The two adjustments address different kinds of timekeeping.

§

Edited by Leo, editor of WhatTimeIsIt.blog

Calculations on this page run in your browser using the IANA time zone database and standard calendar rules. Facts are checked against the government agency, standards body or official source linked in the text. Last reviewed November 10, 2026. See the editorial policy or report an error to hello@whattimeisit.blog.